+44 (0)1785 761344 or 
info@polyflon.co.ukECTFE Film
ECTFE fluoropolymer film
FLONFILM 400 ECTFE film (sometimes referred to as Halar film) is manufactured from ethylenechlorotrifluoroethylene. This material offers outstanding performance over a wide temperature range: from cryogenic to 165C (330F). Halar film provides the highest abrasion resistance of any fluoropolymer film; enjoys superior chemical compatibility, high tensile strength and flexural modulus.
Release applications
FLONFILM 400 ECTFE film exhibits low surface energy making it an excellent choice for release applications. Due to FLONFILM 400’s low specific gravity it provides more surface area/yield than FLONFILM 400 FEP film for composite fabrication.
Electrical applications
The combination of heat stability; its electrical characteristics & barrier properties results in high insulation performance lending itself very well to the electrical & electronics industries. Halar film offers the highest dielectric strength of all fluoropolymer films. Typical applications include electrical tapes, cable insulation, printed circuits, capacitors & flat cable constructions.
General applications
Chlorine cells and solar collectors benefit from the outstanding resistance to weathering & high energy radiation of Halar ECTFE film. With a UL V-0 flammability rating FLONFILM 400 film shows performance suitable for aircraft cabin interiors & fuel cell membranes.
Features & benefits of FLONFILM 400 ECTFE film
- Outstanding release properties.
- Temperature range of -254°C to +165°C.
- High dielectric strength.
- Excellent chemical, radiation, weather & abrasion resistance.
- UL V-0 flammability rating.
- Good barrier properties.
- Can easily be thermoformed: welded, fabricated, laminated.
- Produced & converted in clean room conditions.
| Thickness | Std roll length (m) | |
|---|---|---|
| mm | Inches | |
| 0.0127 | 0.0005 | 367 |
| 0.0254 | 0.001 | 184 |
| 0.0508 | 0.002 | 91 |
| 0.127 | 0.005 | 37 |
| 0.1905 | 0.0075 | 24 |
| 0.254 | 0.010 | 18 |
- Standard roll width: 1220mm (48”) @ 9.5kg.
- Slit widths from 12.7mm (1/2”) up to max width of 1625mm.
- Available in blue, white & clear/natural (standard).
Physical Properties
| Property | ASTM Method | METRIC Value | METRIC Units | IMPERIAL Value | IMPERIAL Units |
|---|---|---|---|---|---|
| GENERAL | |||||
| Specific Gravity | D-792 | 1.68 | 1.68 | ||
| Yield (0.0254mm thk) | 22 | m2/kg | 115 | ft2/lb | |
| Flammability | UL-94 | V-0 | V-0 | ||
| Water Absorption, 24 hrs | <0.01 | % | <0.01 | % | |
| MECHANICAL | |||||
| Tensile Strength | D-882 | 55 | MPa | 8000 | psi |
| Elongation, Ultimate | D-882 | 250 | % | 250 | % |
| Tensile Modulus | D-882 | 1375 | MPa | 200000 | psi |
| Initial Tear Strength, (0.0254mm thk) | D-1004 | 4.4 | N | 450 | gm/mil |
| Propagating Tear Strength, (0.0254mm thk) | D-1922 | 11.6 | N | >1200 | gm/mil |
| Fold Endurance (M.I.T) | D-2176 | >250000 | cycles | >250000 | cycles |
| ELECTRICAL | |||||
| Dielectric Strength, (0.0254mm thk) | D-149 | 216 | kV/mm | 5500 | V/mil |
| Dielectric Constant, 1 kHz | D-150 | 2.55-2.63 | 2.55-2.63 | ||
| Dissipation Factor, 1 kHz | D-150 | <0.005 | <0.005 | ||
| THERMAL | |||||
| Melt Point | D-3418 | 240 | °C | 465 | °F |
| Continuous Service Temperature | 150-170 | °C | 300-340 | °F | |
| Heat Sealing Temperature | 245-260 | °C | 475-500 | °F | |
Click here for printable version – ECTFE Film
The data listed falls within the normal range of product properties but they should not be used to establish specification limits nor used alone as the basis of design. Polyflon Technology Limited assumes no obligation or liability for any advice furnished by it or for results obtained with respect to these products. All such advice is provided gratis and the buyer assumes sole responsibility for the results obtained in reliance thereon.
