Sales: +44 (0)1785 761344 or info@polyflon.co.uk

Fri 30th Jul 10

Ball Valve Actuators & Accessories

Series 6P Pneumatic Part-turn Actuator

The pneumatic part-turn actuator is a maintenance-free rotary piston actuator. The actuator made of plastic provides protection against corrosion. The actuator can be operated with all neutral, gaseous media. Rotary movements p to 90° are possible. The rotary movement is transmitted to the shaft using a rotary piston and high pitch thread. As standard the actuator is available with spring-return. This provides a very high level of safety for the majority of applications, as on the failure of the control air, e.g. due to a power failure, the valve closes automatically. However the actuator is also available as a double acting version for specific applications on request.

Product Advantages

• High torque performance and efficiency
• Maintenance-free

Series 6P Pneumatic part-turn actuator; spring-return
Max. perm. ambient temp	60°C
Volume	0.05 NL
Control pressure	3 – 6 bar
Torque	3 – 6 Nm
Connection thread	BSP 1/4”

Series 6P Actuator Accessories

Pilot Valve

The Pilot valve is a 3/2-way solenoid valve for neutral gases. It can be fitted directly to the pneumatic actuator using a hollow bolt. The part-turn actuator can thus be modified to form an electropneumatic unit. The pilot valve controls the compressed air to the part-turn actuator and automatically vents it on closing.

Due to the low power consumption, computer control is possible. The control function is closed when unpowered. The pilot valve is supplied as standard with manual back-up operation.

Pilot valve for pneum. part-turn actuator; 3/2-way
Max. perm. ambient temp	50°C
Duty cycle	100%
Operating pressure	0 – 10 bar
Power consumption	6,5VA
IP-rating	IP 65
Voltage	24 VDC
Connection thread	BSP1/4”

Electrical Position Indicator

The electrical position indicator is fitted to the part-turn actuator. As standard it is equipped with two proximity switches. Using threaded spindles the two inductive proximity sensors can be precisely adjusted continuously and independently. They are not subject to any wear.

Product advantages

• Can be added later
• Compact shape
• Corrosion-free
• Wear-free switch, contact-less detection
• IP-rating IP 65 in accordance with DIN 40050
• Proximity switch with PTB approval in accordance with NAMUR DIN 19234 available on request.

Electrical position indicator for pneum. part-turn actuator; three-wire
Max. perm. ambient temp	60°C
Function	PNP
Voltage	10 – 30 VDC
Rating	< 200 mA
IP-rating	IP 65

Optical Position Indicator

The optical position indicator is the simplest form of position indication. This is provided by a red signal pin to be fitted to the part-turn actuator; this indicates the switch position.

Optical position indicator for pneum. part-turn actuator
Colour	red

Series 6E Electrical Part-turn Actuator

For more demanding switching requirements, an electrical part-turn actuator is recommended. The switching times are extremely short (approx. 1 sec / 90°). The powerful electric motor with planetary gear provides safety – burn-out or hot windings are avoided. The electrical part-turn actuator can be controlled with an interface on a computer (RS 232) or directly using a PLC.

Product Advantages

• Numerous switching options
• Short switching times
• Safe and reliable

Series 6E Electrical part-turn actuator
Max. perm. ambient temp	70°C
Voltage	24 VDC
Torque	7.7-15.4 Nm
IP-rating	IP 65
Connection	PG 9

Click here for printable version – Ball Valve Actuators & accessories

The data listed falls within the normal range of product properties but they should not be used to establish specification limits nor used alone as the basis of design. Polyflon Technology Limited assumes no obligation or liability for any advice furnished by it or for results obtained with respect to these products. All such advice is provided gratis and the buyer assumes sole responsibility for the results obtained in reliance thereon.